Get exclusive volume discounts, bulk pricing updates, and new product alerts delivered directly to your inbox.
By subscribing, you agree to our Terms of Service and Privacy Policy.
Direct access to our certified experts
Width: 5.18 in
Height: 2.7 in
Length: 6.9 in
Weight: 370 g
Accuracy: ± 0.01 %
Channels: One channel standard, second channel optional
Mounting: Panel
Materials: Polycarbonate, Polyester Nonwoven Fabric, Neoprene, Stainless Steel
Input Type: Voltage, Current
Resolution: 16-bit A/D
Form factor: 1/8 DIN
Runout Mode: Updated at rate selected by digital filter. Runout is normally stored in memory and recalled via front-panel switch, over the serial interface, or by selecting runout display mode on rear connector.
Display Note: -32768 to 32767 with programmable decimal points; 14 mm (0.56") red LED
Display Type: LED
Reading Rate: Limited to 1000/s divided by number of channels
Accuracy Note: ± 0.01% of reading ± 1 count of A/D @ 25°C (77°F)
Output Detail: Analog Output: 4 to 20 mA; tracks display reading; voltage outputs will sink or source 1 mA; 300V isolation between analog outputs and instrument ground, Relays: Dual 115 Vac, 2.5 A, form “A” relay contacts (isolated transistor outputs not available when relays are installed); limit #1 and limit #2 activate the relay contacts
Output Method: RJ11 jack for serial interface
Output Signal: Current
Remote Inputs: Display Peak, Display Runout, Reading, Reset Peak, Runout Reading, Tare
Sampling Rate: 1000 Hz
Control Output: Relays: Dual 115 Vac 2.5 A
Data Interface: N/A
Digital Filter: Programmable Cutoff Frequency
Peak Detection: Updated at rate selected by digital filter, peak stored in memoryrogrammed to give limit #1 output up to 100 seconds after a programmed limit is reached. This output can be used to reset the peak reading by tying limit #1 output to remote input
Rollover Error: ± 2 counts of A/D @ 25°C (77°F)
Supply Voltage: 18 to 36 Vdc
supply-voltage: 18 to 36 Vdc
Impedance Input: 0 to 200 mVdc,10 x 10¹² Ω; 0 to 5 Vdc,1 MΩ; 0 to 10 Vdc,1 MΩ; 4 to 20 mA, 10 Ω.
Calibration Note: Digital calibration via front-panel button switches; no potentiometer adjustments; access code prevents unauthorized calibration switches
Input Range Note: 0 to 200 mVdc, 0 to 5 Vdc, 0 to 10 Vdc, 4 to 20 mA
Measurement Type: Current, Strain, Voltage
Number of Digits: 5
Number of Inputs: 1
SetPoint Outputs: 4 isolated open collector transistor outputs rated 30 Vdc maximum; will sink up to 50 mA; 300 V isolation between limit outputs and system ground; limit #1 can be programmed to be delayed from 1 to 100 seconds
Cutout Dimensions: 2.45 x 5.06 in
Electrical Output: 4 to 20 mA
Power Consumption: 8 W
Sensor Excitation: ± 15 Vdc, ± 5 Vdc @ ± 50 mA
Supply Power Note: 18 to 36 Vdc@ 600 mA
Supply Power Type: DC
Convert/Hold Input: Normally high; if pulled low, holds display
Input Bias Current: ± 50 nA maximum ± 100 pA/°C (per input channel)
Input Analog Filter: 4-pole active anti-alias; 500 Hz cutoff on single-channel unit and 250 Hz cutoff on dual-channel unit
Input Configuration: Front Keypad
Internal Resolution: 16 bit
Settable Parameters: Digital Filter, Limits, Offset, Span
Electrical Connection: Screw Terminal
Operating Temperature, Max: 60 °C
Operating Temperature, Min: -20 °C
